HP ProCurve 2626 Switch`i VLAN`de seadistamine

As you can see, I have a device connected to a port on each switch in the same VLAN. The idea here is to have the same VLAN on both switches and allow both devices communicate over that VLAN. NOTE: when going from switch to switch a crossover cable is usually required. However, the HP Procurve perform auto MDI/MDI-X which eliminates the need for one. First, we will login via the console port to configure the switch. See below:

ProCurve Switch 2810-48G# conf t

ProCurve Switch 2810-48G(config)# vlan 100 name VLAN100

ProCurve Switch 2810-48G(config)# end

ProCurve Switch 2810-48G# show vlan

Status and Counters – VLAN Information

Maximum VLANs to support : 8

Primary VLAN : DEFAULT_VLAN

Management VLAN :

802.1Q VLAN ID Name         Status       Voice Jumbo

————– ———— ———— —– —–

1              DEFAULT_VLAN Port-based   No    No

100            VLAN100      Port-based   No    No

ProCurve Switch 2810-48G# show run

 

Running configuration:

; J9022A Configuration Editor; Created on release #N.11.06

hostname “ProCurve Switch 2810-48G”

snmp-server community “public” Unrestricted

vlan 1

name “DEFAULT_VLAN”

untagged 1-48

ip address dhcp-bootp

exit

vlan 100

name “VLAN100”

exit

 

As you can see, we created a VLAN with a VLAN name, displayed all the VLANs currently configured, and viewed the running configuration. This configuration will not be saved if the switch is rebooted until you issue a “wr mem” command.

Next, we will add a second VLAN and tag the arbitrary ports to trunk them through. Ports designated as “untagged” belong to a specific VLAN and will only be able to communicate with other ports on the same VLAN. Ports designated as “tagged” ports belong to multiple VLANs and will be able to communicate with multiple VLANs. See the configuration below:

ProCurve Switch 2810-48G# conf t

ProCurve Switch 2810-48G(config)# vlan  100

ProCurve Switch 2810-48G(vlan-100)# untagged 1-11

ProCurve Switch 2810-48G(vlan-100)# tagged 24

ProCurve Switch 2810-48G(vlan-100)# exit

ProCurve Switch 2810-48G(config)# conf  t

ProCurve Switch 2810-48G(config)# vlan 200 name “VLAN200”

ProCurve Switch 2810-48G(config)# vlan 200

ProCurve Switch 2810-48G(vlan-200)# untagged 13-16

ProCurve Switch 2810-48G(vlan-200)# tagged 24

ProCurve Switch 2810-48G(vlan-200)# exit

ProCurve Switch 2810-48G(config)# sh ru

ProCurve Switch 2810-48G# sh ru

 

Running configuration:

; J9022A Configuration Editor; Created on release #N.11.06

hostname “ProCurve Switch 2810-48G”

snmp-server community “public” Unrestricted

vlan 1

name “DEFAULT_VLAN”

untagged 12,17-48

ip address dhcp-bootp

no untagged 1-11,13-16

exit

vlan 100

name “VLAN100”

untagged 1-11

no ip address

tagged 24

exit

vlan 200

name “VLAN200”

untagged 13-16

no ip address

tagged 24

exit

ProCurve Switch 2810-48G# wr mem

ProCurve Switch 2810-48G# sh vlan

Status and Counters – VLAN Information

Maximum VLANs to support : 8

Primary VLAN : DEFAULT_VLAN

Management VLAN :

802.1Q VLAN ID Name         Status       Voice Jumbo

————– ———— ———— —– —–

1              DEFAULT_VLAN Port-based   No    No

100            VLAN100      Port-based   No    No

200            VLAN200      Port-based   No    No

 

Remember, no IP addresses have been configured for the switch or any VLANs which reside on this switch. The examples and configuration above allowed devices on port 16 of each switch (members of VLAN 200) to communicate. By plugging into different VLANs (VLAN 100 and VLAN 200) the devices were unable to communicate. A “wr mem” command was issued here to ensure the configuration was saved if the switch is rebooted.

 

To configure an IP address for VLANs 100 and 200, see below:

ProCurve Switch 2810-48G# conf t

ProCurve Switch 2810-48G(config)# vlan 100

ProCurve Switch 2810-48G(vlan-100)# ip address 10.15.15.200 255.255.255.0

ProCurve Switch 2810-48G(vlan-100)# exit

ProCurve Switch 2810-48G(config)# vlan 200

ProCurve Switch 2810-48G(vlan-200)# ip address 10.15.16.200 255.255.255.0

ProCurve Switch 2810-48G(vlan-200)# sh vlan

Status and Counters – VLAN Information

Maximum VLANs to support : 8

Primary VLAN : DEFAULT_VLAN

Management VLAN :

802.1Q VLAN ID Name         Status       Voice Jumbo

————– ———— ———— —– —–

1              DEFAULT_VLAN Port-based   No    No

100            VLAN100      Port-based   No    No

200            VLAN200      Port-based   No    No

ProCurve Switch 2810-48G(vlan-200)# sh ru

Running configuration:

; J9022A Configuration Editor; Created on release #N.11.06

hostname “ProCurve Switch 2810-48G”

snmp-server community “public” Unrestricted

vlan 1

name “DEFAULT_VLAN”

untagged 12,17-48

ip address dhcp-bootp

no untagged 1-11,13-16

exit

vlan 100

name “VLAN100”

untagged 1-11

ip address 10.15.15.200 255.255.255.0

tagged 24

exit

vlan 200

name “VLAN200”

untagged 13-16

ip address 10.15.16.200 255.255.255.0

tagged 24

exit

ProCurve Switch 2810-48G(vlan-200)#

Once the IP addresses are set on each VLAN, devices in those VLANs will be able to ping the IP address of the VLAN as long as they have the same network and subnet scheme.

he user can restore the factory default configuration either on the switch itself, or through the switch console.

To execute the factory default reset on the switch, perform these steps:

Using pointed objects, simultaneously press both the Reset and Clear buttons on the front of the switch. The power and fault lights come on.

Continue to press the Clear button while releasing the Reset button.

When the Self Test LED begins to blink, release the Clear button.

The switch will then complete its self test and begin operating with its configuration restored to the factory default settings.

To restore the factory default configuration using the console, execute the erase startup-config command from the console command prompt.